河北会泉泵业有限公司
五金通钻石会员 第13年
已通过企业工商认证
公司服务热线
13582138818
ZJW200-250压滤机X柱塞泵前期入料流量大
冬季轴承油如何更换？更换新的油之前，应把旧油排放干净再加入新油。在排放旧油时应观察旧油的清洁度，如果清洁度较高可收集起来二次利用，如果比较浑浊杂质多应直接倒掉，出现这种情况，在排完油后应用柴油等清洗油清洗轴承箱内的污物杂质，保证内部清洁度。
一、ZJW压滤机入料X泵特点
1、水力设计、结构设计X新颖、效率高、搞磨蚀、运行平稳可靠2、前期入料流量大、压力低；3、后期压榨流量小、压力高；
4、轴密封简单可靠，不注水、不用机械密封，无泄漏;5、压滤入料不用变频调速，输送浓度高。
二、ZJW压滤机入料X泵简述
ZJW-II Special Pump is a special performance of impurity pump.In recent years, by the industry called "Filter machine special feed divssure pump."The pump from the back side of the suction slurry, filler seal without leakage, more importantly, its flow, lift curve is very steep, very suitable for some special working conditions.
ZJW-II Filter Press Special feed pump listed in the main technology is the pump in the 1480r/min data, for the requirements of low divssure conditions, can be appropriate to cut the impeller or reduce the number of pumps to solve, but also can choose my factory production of ZJ series slurry pump, ZJ pump mechanical seal and ZJW-II pump as "no leakage."This information only provides the base dimensions of several direct-linked transmissions.Because the terrain limit or change the number of pump transfer needs the base size of the belt drive, there is a field to provide specific data designed separately.Belt transmission mode generally has tailstock type, parallel type, back bracket type transmission.
ZJW-II Filter Press Special feed pump for the divssurized suction pump, the suction process is small, it is recommended that the feed liquid surface higher than the center of the pump.Import and export pipeline diameter is generally the same or slightly larger than the pump import and export diameter, because the slurry concentration is mostly higher, so the pump inlet pipeline should not be too long, so as not to affect the suction
冬季轴承油如何更换？更换新的油之前，应把旧油排放干净再加入新油。在排放旧油时应观察旧油的清洁度，如果清洁度较高可收集起来二次利用，如果比较浑浊杂质多应直接倒掉，出现这种情况，在排完油后应用柴油等清洗油清洗轴承箱内的污物杂质，保证内部清洁度。
ZJW Filter Press Feed Special pump from the rear side suction slurry, filler seal without leakage, more importantly, its flow, lift curve is very steep, very suitable for divssure filter working conditions.
ZJW Filter Press Feed special pump listed in the main technology is the pump in the 1480r/min data, for the requirements of low divssure conditions, can be appropriate to cut the impeller or reduce the number of pumps to solve, but also can choose my factory production of ZJ series slurry pump, ZJ pump mechanical seal and ZJW-II pump as "no leakage."This information only provides the base dimensions of several direct-linked transmissions.Because the terrain limit or change the number of pump transfer needs the base size of the belt drive, there is a field to provide specific data designed separately.Belt transmission mode generally has tailstock type, parallel type, back bracket type transmission.
ZJW Filter Press Feed special pump for the divssurized suction pump, the suction process is small, it is suggested that the feed liquid surface is higher than the center of the pump.Import and export pipeline diameter is generally the same or slightly larger than the pump import and export diameter, because the slurry concentration is mostly higher, so the pump import pipeline should not be too long
ZJW200-250压滤机X柱塞泵前期入料流量大
压滤机入料泵的正确操作使用压滤机入料泵的使用操作并不复杂，正确的操作能损失维修费用。部分客户由于误操作泵损坏或者造成泵的性能减弱使用寿命等，不仅影响企业的生产效率还了设备使用成本，所以这些情况要尽可能避免出现。
三、ZJW压滤机入料X泵选型
与其它一般性输送用泵区别很大，一般性输送用泵的选型，主要是选用某条流量、扬程曲线上某个点或很短一段曲线所对应的性能。而压滤机的工作特性是：滤室内滤饼的逐渐形成，入料阻力也随之加大，要求入料泵从起始时的大流量、低扬程自行过滤末期的小流量、高扬程。反映到曲线上是需要较长的甚至一条较完整的而且是越陡越好的流量、扬程曲线。除此特性外，还要求泵工作在高压时，不用轴封水和无泄漏，为建设环保工厂创造条件。wjhuiquan6.26
ZJW压滤机入料X泵功率配置入料泵的功率损耗在入料的初始阶段，所以要详细计算由入料泵往压滤机注浆的压力，然后按该压力对应的该泵的流量，扬程配用功率。如此较为准确、节约。由于各工厂压滤的实际布置差异，当入料泵与滤机之间的沿程阻力较大时（如：泵距压滤机较远、管道直径偏小、弯头与闸门较多、浆液粘度较大等），会入料泵的扬程损失，成饼压力。滤饼水份偏高与单循环时间拉长，的生产效率大为，所以必须要合理的管路配置。
适用于工程配套、工业、民用建筑给水排水、暖通、制冷、消防、排污、油库、油轮、、、印染等企作业单位。为您供应更便利的售前、售后效力。除了活泼满意国内商场需求的一同，黎凯泵业决计立异，根据国外客户要求，许多新产品：如浴缸泵，鱼缸泵，冲浪泵，泵，微型自吸离心泵，太阳能泵。管道泵，和加热泵等。本公司65%出售人员具有海外留学布景，熟练把握多门外语，更加快速准确消费者需求，供应高的产品和效力，客户无需为产品的参数和功用苦恼，黎凯X的出售人员能够快速的对产品信息进行分析，X的工程师快速的对您的需求选择适合的产品，而且供应合理可靠的建议。黎凯泵业X出产各类水泵，多年的出产阅历保证产品高水平制造工艺。
