离心清水泵@通州离心清水泵@离心清水泵【负责安装吗】
Medium-Open pump is a wide range of general-purpose machinery and equipment, it is widely used in petroleum, chemical, power metallurgy, mining, ship selection, light industry, agriculture, civil and national defense departments, in the national economy occupies an important position. The so-called reasonable choice of open pump, is to consider the pump unit and pumping station investment and operating costs, such as comdivhensive technical and economic indicators, so that it conforms to the economic, safety, applicable principles. Specifically, there are several aspects.
S、SH型泵系单X、双吸、泵壳中开式离心泵。供吸送清水及物理化学性质类似于水的。 本型泵扬程在9-140米时，流量为126-12500立方米/时，温度不得X过80度，适合工厂、矿山、城市给水、电站、大型水利工程、农田灌溉和排涝等，48SH-22型大型泵还可作热电站循环泵使用。wjhuiquan4.12
So that the dynamic ring and static ring wear, spring and shaft rust wear, sealant ring wear, aging, deformation, etc., can cause sealing leakage, must repair or replace new parts. The sealing surface of the dynamic ring and static ring shall not he cracks, corners, scratches, hemp points, flying edges and partial grinding, scratches, hemp points can not run through the entire sealing end surface. If the fixed static and dynamic ring is used, the height of the convex of the static and dynamic ring is not less than 3mm, and the height of a single convex is not less than lmm, so as not to affect the heat dissipation. 3 Dynamic ring After installation should be guaranteed to move flexibly on the shaft, the dynamic ring divssure on the spring should be able to bounce back freely. And he a certificate. Mechanical seal after long-term operation to take quality control measures mechanical seal before leing the factory must do sealing performance test to maintain the vertical and parallel of the static and dynamic ring.
泵型号的意义：
10SH-13A 10—吸水口直径被25除（即该泵吸水口直径为250毫米）
SH—单吸双吸离心清水泵
13—比转数被10除（即该泵的比转数为130）
A—表示该泵换了不同外径的叶轮
S型泵流量范围更广：50—18000立方米/时。 如500S35A 500—泵的口径（毫米）
S—单吸双吸，中心离心清水泵
35—设计点扬程（M）
A—叶轮次切割
离心清水泵@通州离心清水泵@离心清水泵【负责安装吗】
水环泵的压缩比由泵的吸气口终了位置和排气口开始位置所决定。因为吸气口终止位置决定着吸气腔气体的体积，而排气口开始的位置决定着排气时压缩了的气体的体积。对已经确定了结构尺寸的水环泵，可以求出其压缩比。
SH型泵及S型泵统称为双吸泵，其工作性能及配用电机大体相同。需要说明的是泵的方向不同，从电机端看SH型泵为逆时针，而S型泵则顺时针。在实际使用中SH型泵更加广泛.
性能参数表：
型号 | 流量Q | 总扬程 H (m) | 转速 N (r/min) | 功率N(Kw) | 效率 η （%） | 必须汽蚀余量 (m) | 叶轮 直径 mm | 泵 kg |
m3/h | L/s | | | 轴功率 | 电机功率 | | | | |
6Sh-6 150s78 | 126 | 35 | 84 | 2900 | 40 | 55 | 72 | 5 | 248 | 150 |
162 | 45 | 78 | 45.8 | 75 |
198 | 55 | 70 | 51.0 | 74 |
6Sh-6A 150S78A | 112 | 31 | 67 | 2900 | 30 | 45 | 68 | 5 | 220 | 150 |
144 | 40 | 62 | 33.8 | 72 |
180 | 50 | 55 | 38.5 | 70 |
6Sh-9 150S50 | 130 | 36.2 | 52 | 2900 | 25.3 | 37 | 74 | 5 | 200 | 145 |
170 | 47.2 | 47.6 | 27.6 | 80 |
220 | 61.2 | 35 | 31.3 | 67 |
6Sh-9A 150S50A | 120 | 31 | 43.8 | 2900 | 18.5 | 30 | 72 | 5 | 186 | 145 |
144 | 40 | 40 | 20.9 | 75 |
180 | 50 | 35 | 24.5 | 70 |
8Sh-6 200S95 | 180 | 50 | 100 | 2900 | 79.1 | 110 | 62 | 5.5 | 284 | 245 |
234 | 65 | 93.5 | 85.0 | 71 |
288 | 80 | 82.5 | 88.6 | 73 |
8Sh-6A 200S95A | 160 | 44.5 | 85.1 | 2900 | 60.8 | 90 | 61 | 5.5 | 262 | 245 |
215 | 59.7 | 75.6 | 64.2 | 69 |
265 | 73.6 | 70.2 | 71.4 | 71 |
8Sh-9 200S63 | 213 | 60 | 69 | 2900 | 55 | 75 | 74 | 4.7 5.5 7 | 236 | 265 |
288 | 80 | 62.5 | 61.3 | 80 |
351 | 97.5 | 50 | 67.8 | 70.5 |
8Sh-9A 200S63A | 180 | 50 | 54.5 | 2900 | 41 | 55 | 65 | 4.5 5.0 6.2 | 220 | 265 |
270 | 70 | 46 | 48.3 | 70 |
324 | 90 | 37.5 | 51 | 65 |
8Sh-13 200S42 | 126216 | 3560 | 8448 | 2900 | 34.9 | 45 | 81 | 5.0 6.4 8.2 | 204 | 219 |
162288 | 4580 | 7841.3 | 38.1 | 85 |
198342 | 5595 | 7035 | 40.2 | 81 |
8SA-10 8Sh-13 200S42 | 198 | 55 | 43 | 2900 | 30.5 | 37 | 76 | 4.8 5.8 7 | 139 | 219 |
270 | 75 | 36 | 33.1 | 80 |
310 | 86 | 31 | 34.4 | 76 |
10Sh-6 250S65 | 360 | 100 | 71 | 1450 | 91.5 | 132 | 76 | 4 | 460 | 565 |
486 | 135 | 65.1 | 109 | 79 |
612 | 170 | 56 | 129.6 | 72 |
10Sh-6A 250S65A | 342 | 95 | 61 | 1450 | 76.7 | 110 | 74 | 4 | 436 | 565 |
468 | 135 | 54 | 89.4 | 77 |
540 | 150 | 50 | 98 | 75 |
10Sh-9 250S39 | 360 | 100 | 42.5 | 1450 | 55.5 | 75 | 75 | 4 | 367 | 428 |
486 | 135 | 38.5 | 61.5 | 83 |
612 | 170 | 32.5 | 67.7 | 80 |
10Sh-9A 250S39A | 324 | 90 | 35.5 | 1450 | 40.2 | 55 | 78 | 4 | 338 | 428 |
468 | 130 | 30.5 | 45.7 | 85 |
576 | 160 | 25 | 47.8 | 82 |
10Sh-13 250S24 | 360 | 100 | 27 | 1450 | 33.1 | 45 | 80 | 4 | 296 | 420 |
486 | 135 | 23.5 | 36.2 | 86 |
576 | 160 | 19 | 36.4 | 82 |
10Sh-13A 250S24A | 342 | 95 | 22.2 | 1450 | 25.8 | 37 | 80 | 4 | 270 | 420 |
414 | 115 | 20.3 | 27.6 | 83 |
482 | 134 | 17.4 | 28.6 | 80 |
10Sh-19 250S14 | 360 | 100 | 17.5 | 1450 | 21.4 | 30 | 80 | 4 | 240 | 405 |
486 | 135 | 14 | 21.8 | 85 |
576 | 160 | 11 | 22.1 | 78 |
10Sh-19A 250S14A | 320 | 89 | 13.7 | 1450 | 15.4 | 22 | 78 | 4 | 224 | 405 |
432 | 120 | 11 | 15.8 | 82 |
504 | 140 | 8.6 | 15.8 | 75 |
离心清水泵@通州离心清水泵@离心清水泵【负责安装吗】
Medium-Open pump is a wide range of general-purpose machinery and equipment, it is widely used in petroleum, chemical, power metallurgy, mining, ship selection, light industry, agriculture, civil and national defense departments, in the national economy occupies an important position. The so-called reasonable choice of open pump, is to consider the pump unit and pumping station investment and operating costs, such as comdivhensive technical and economic indicators, so that it conforms to the economic, safety, applicable principles. Specifically, there are several aspects.
修补便利等X点。一起本企业水泵产品功能达以到国内X水平，为一些关键工程，环保，工业，农业缔造，等做出了较大奉献，了宽广用户，产品配套单位的好评和X。功能可靠节能企业产品具有规划合理 本厂通过了ISO9001认证。每件产品都严峻“按图样。
